Products → Conveyors
Curved Conveyor (2 sections)
Approximately 60 deg conveyor each section. 2 sections make more then a 90 deg. All stainless steel with dual height guide rails. Has plastic channel for conveyor to ride. Approximately 31" long x 4.5" wide, no belting. Sections aren't 100% complete some minor things missing like a rail holder, nuts & bolts but they are in good condition.
Nuspack Engineering 180 Deg Conveyor
180 deg. stainless steel conveyor with mild steel legs. The belt is 7.5" wide x 174" long. It has a 18.5" long straight section before the curve, then there is a 39.75" long straight section between the corners and a 19" long straight section after the last curve. The top of the belt is 38" from the floor and has heights adjustable feet. It has stainless steel guide rails. Comes with a variable speed controller with digital readout. Last used in a food facility. In good condition.
Mild steel conveyor. Belt is 12" wide x 81" long. It sits on a slight incline from 32" tall to 36" tall but that can be leveled out to run flat. In good condition. Last used in a food facility.
Kalish 90 Degree Conveyor Corners
View DetailsModel: 90000
Stainless steel 90 degree corners 11" diameter. No motor for either. One has a guide rail, the other one doesn't.
Power Roller Conveyor
Mild steel power roller conveyor. The conveyor is 15.5" wide (21" wide overall) x 120" long. It has steel rollers and runs right to left. Height adjustable legs on casters. Control box has start, stop and e-stop. In good working condition.
The conveyor is 104" long x 15" wide overall with 12.5" rollers. It has hooks on one end to attach to another machine. Mild steel. No legs. In good condition.
Stainless steel conveyor. The belt is 30" wide x 26" long on an incline (could run flat if you adjust the legs). The low end is 29.25" from the floor and goes up to 35.5". It has a washdown motor. On height adjusable legs on casters. In good condition but the belt needs cleaning.
Stainless steel conveyor. The belt is 29.5" wide x 60" long and currently sits 36" from the floor. It has height adjustable legs. In good condition. Last used in a food facility.
Marchant Schmidt Wash Belt Conveyor
Stainless steel conveyor with belt washer. The belt is 12" wide x 120" long overall. It has a 38" long straight section and a 82" long incline section. The high end is 37.54" from the floor the low end is 29.25" from the floor. The belt washing bin is 21" long x 12.5" deep. It has a 2" & 2.5" outside diameter sani clamp connection inlets on one side and a 3" diameter inlet on the other side that has a spray bar to clean the belt. There is a Baldor 230 / 460, 3 ph, 1.5 hp motor for the washstation. It also has an overflow pipe on one side. On casters in good condition. Because of a cross piece from the frame going across the conveyor it can only handle products no taller than 5.75"
Formax Shuttle Conveyor
View DetailsModel: SC-6
Stainless steel conveyor with stainless mesh belt. The belt is 7" wide and is 75.5" long fully extended. When the product hits the photo eye it engages the conveyor to retract. The belt retracts 21.5". It has variable speed controls. In good working condition. Last used in a food facility.
Cleated Incline Conveyor
All stainless steel incline conveyor. The conveyor is 27" wide overall. The belt is 12" wide x 28" long flat section along the floor and 132" long incline (11 feet). It has 6" spacing between cleats that are 1.5" tall. The belt also has corigated sidewalls. One side is 1" tall the other is 1.5" tall. The belt starts at 12" from the floor and has a height of 66.5" from the floor. It has an on / off switch. On casters. In good working condition. Last used in a food facility.